Maestro
Live demo — data resets daily at 03:00 UTC. Nothing you enter is saved.
3D Printer Service Book
ETT00000011 · Rev R0
genericin_progress
Generated 2026-07-26 14:05 UTC

Living service log for E-Sharp's 3D printer(s). Records maintenance events, part replacements, calibration notes, observed issues and their resolutions, and any configuration changes. No defined end date — intended as a permanent running log.

Coverage 0%
Done 0%
Requirements 0
Test Cases 0
Records 0

Milestones

No milestones defined.

Items (13)

Code Status Severity Kind Title Date
E-001 open info concept Fleet overview — 4 Bambu Lab printers (Hades, Posedion, Zeus, Sisyphus) 2026-06-11
E-002 open info concept Recommended spare parts to keep in stock 2026-06-11
E-003 open info concept Installed upgrades and printed mods 2026-06-11
E-004 open info issue Zeus — filament not feeding through; extruder gears worn out 2026-06-11
E-005 open info issue Hades — filament completely stuck in extruder, could not retract 2026-06-11
E-006 open info notice Hades — service history 2026-06-11
E-007 open info notice Posedion — service history 2026-06-11
E-008 open info notice Zeus — service history 2026-06-11
E-009 open info concept P1S error codes — 03xx: Motion, calibration & mechanical (37 codes) 2026-06-11
E-010 open info concept P1S error codes — 0Cxx / 10xx: Data link & timelapse warnings (8 codes) 2026-06-11
E-011 open info concept P1S error codes — 05xx: System, network, firmware & print management (159 codes) 2026-06-11
E-012 open info concept P1S error codes — 07xx: AMS filament system (161 codes) 2026-06-11
E-013 open info concept P1S error codes — 18xx: AMS-HT filament system (158 codes) 2026-06-11

Requirements

No requirements recorded.

Test Cases

No test cases recorded.

Verification Records

No verification records.

Concepts

Active exploration (8) — ideas still being shaped.

E-001 Fleet overview — 4 Bambu Lab printers (Hades, Posedion, Zeus, Sisyphus)open 2026-06-11

E-Sharp operates four Bambu Lab 3D printers, each with an internal name:

Name Model Notes
Hades Bambu Lab P1S Hardened steel hotend + extruder gears installed 2025-05-23
Posedion Bambu Lab P1S Hardened steel hotend + extruder gears installed 2025-05-23
Zeus Bambu Lab P1S Hardened steel hotend + extruder gears installed 2025-05-23
Sisyphus Bambu Lab A1 No service events logged yet

All P1S machines have AMS units. Sisyphus (A1) has AMS.

E-002 Recommended spare parts to keep in stockopen 2026-06-11

General (all machines)

P1S specific

A1 specific

E-003 Installed upgrades and printed modsopen 2026-06-11

P1S — Purchased upgrades (installed on Hades, Posedion, Zeus)

P1S — 3D printed mods

A1 — Purchased upgrades (installed on Sisyphus)

A1 — 3D printed mods

E-009 P1S error codes — 03xx: Motion, calibration & mechanical (37 codes)open 2026-06-11

Bambu Lab P1S error codes — motion, calibration, mechanical and print-control errors. Source: BambuStudio hms_en_01P.json

Code Description
03004000 Z axis homing failed; the task has been stopped.
0300800B The cutter is stuck. Please make sure the cutter handle is out and check the filament sensor cable connection.
0300400C The task was canceled.
03008018 Chamber temperature malfunction.
03004002 Auto Bed Leveling failed; the task has been stopped.
0300400A Mechanical resonance frequency identification failed.
03008005 Toolhead front cover fell off. Please remount the front cover and check to make sure your print is going okay.
03008010 The hotend cooling fan speed is abnormal.
03008017 Foreign objects detected on heatbed. Please check and clean the heatbed. Then, select "Resume" to resume the print job.
0300800D Detected that the extruder is not extruding normally. If the defects are acceptable, select "Resume" to resume the print job.
03004005 The hotend cooling fan speed is abnormal.
03008008 Nozzle temperature malfunction. Check the Assistant page and resolve the issue before retrying heating.
03008019 Build plate not detected. Please ensure there are no bulges or debris on the plate and that the nozzle is clean.
03008013 Printing paused due to the pause command added to the printing file.
03004013 Printing cannot be initiated while AMS is drying.
0300400D Resume failed after power loss.
03008009 Heatbed temperature malfunction.
03008014 The nozzle is covered with filament, or the build plate is installed incorrectly. Please cancel this print and clean the nozzle or adjust the build plate.
0300800F The door seems to be open, so printing was paused.
03008001 Printing was paused by the user. You can select "Resume" to continue printing.
03004067 Calibration result is over the threshold.
03004020 The nozzle presence detection failed. Please check the Assistant for details.
0300800E The print file is not available. Please check to see if the storage media has been removed.
03004006 The nozzle is clogged.
03004009 Homing XY axis failed.
0300400E The motor self-check failed.
03008000 Printing was paused for unknown reason. You can select "Resume" to resume the print job.
03008016 The nozzle is clogged with filament. Please cancel this print and clean the nozzle or select "Resume" to resume.
03008004 Filament ran out. Please load new filament.
0300800C Multiple motion steps lost detected. Please check if the toolhead is blocked by obstructions or making abnormal noise. If the print shows layer shifting, refer to the Wiki for maintenance.
0300400B Internal communication exception.
03004001 The printer timed out waiting for the nozzle to cool down before homing.
03004008 The AMS failed to change filament.
03008007 There was an unfinished print job when the printer lost power. If the model is still on the build plate, you can try resuming.
03004014 Homing Z axis failed: temperature control abnormality.
0300806E Abnormal nozzle temperature control detected; the heating module may be damaged. Please disconnect the power immediately and stop using the device.
0300806F Abnormal temperature rise detected on the heatbed. The heating module may be damaged. Please power off the device immediately and stop using it.
E-010 P1S error codes — 0Cxx / 10xx: Data link & timelapse warnings (8 codes)open 2026-06-11

Bambu Lab P1S error codes — data link errors and timelapse/camera warnings. Source: BambuStudio hms_en_01P.json

Code Description
0C00402C Device data link error. Please reboot the printer.

10xx — Timelapse & camera warnings (7 codes)

Code Description
10014001 Timelapse is not supported as Spiral Vase mode is enabled in slicing presets.
10018003 The time-lapse mode is set to Traditional in the slicing file. This may cause surface defects. Would you like to enable it?
10014002 Timelapse is not supported as the Print sequence is set to "By object".
10018004 Prime Tower is not enabled and time-lapse mode is set to Smooth in slicing file. This may cause surface defects. Would you like to enable it?
1000C003 Enabling Timelapse in traditional mode may cause defects; please activate this feature as needed.
1000C002 Printing CF material with stainless steel may cause nozzle damage.
1000C001 High bed temperature may lead to filament clogging in the nozzle. You may open the chamber door.
E-011 P1S error codes — 05xx: System, network, firmware & print management (159 codes)open 2026-06-11

Bambu Lab P1S error codes — system, network, firmware, storage, and print management errors. Source: BambuStudio hms_en_01P.json

Code Description
0500400E Printing was cancelled.
05004006 Not enough free storage space. Restoring to factory settings can free up space.
0501401E Cloud response is invalid. If issue persists, contact customer support.
05004003 Printer unable to parse the file. Please resend your print job.
05014034 Slicing progress not updated for a long time, print task exited. Confirm parameters and reinitiate.
05004002 Unsupported print file path or name. Please resend the print job.
05014021 Cloud access failed — network instability. Try moving printer closer to router.
0500401D Cloud access failed — network instability. Try moving printer closer to router.
05004040 Printer has reached power limit. Connect a dedicated power adapter to AMS to enable drying.
05004041 AMS drying cannot be started during printing.
0501401C Cloud access rejected. If issue persists, contact customer support.
05004027 Cloud access failed — network instability. Try moving printer closer to router.
05004025 Cloud response is invalid. If issue persists, contact customer support.
05008036 Sliced file not consistent with current printer model. Continue?
05004023 Cloud access rejected. If issue persists, contact customer support.
0501401D Cloud access failed — network instability. Try moving printer closer to router.
0501401B Cloud response is invalid. If issue persists, contact customer support.
05004026 Cloud access rejected. If issue persists, contact customer support.
0500400A File name not supported. Please rename and restart the print job.
05004007 Device requires a repair upgrade; printing currently unavailable.
0500401C Cloud access rejected. If issue persists, contact customer support.
05004031 Accessory firmware does not match printer. Please upgrade on the "Firmware" page.
0500402A Failed to connect to router — wireless interference or too far from router.
05014039 Device login has expired; please try to bind again.
0500401E Cloud response is invalid. If issue persists, contact customer support.
05014032 QR code binding in progress; device discovery binding cannot be performed.
0500402B Router connection failed due to incorrect password. Please check the password.
05014023 Cloud access rejected. If issue persists, contact customer support.
05004004 Device is busy; cannot start new task. Wait for current task to complete.
05014038 Regional settings do not match printer; please check printer's regional settings.
05004037 Sliced file not compatible with current printer model. Cannot be printed.
05014027 Cloud access failed — network instability. Try moving printer closer to router.
05004043 Due to power limitations, only one AMS is allowed to use device power for drying.
05014019 Printer already bound. Please unbind and try again.
05004033 AMS firmware does not match printer. Please upgrade on the "Firmware" page.
0500402C Failed to obtain IP address — wireless interference or DHCP pool full. Check router settings.
05004021 Cloud access failed — network instability. Try moving printer closer to router.
05014017 Binding failed. Please retry or restart printer and retry.
05004009 Print jobs not allowed while updating logs.
05014026 Cloud access rejected. If issue persists, contact customer support.
05004005 Print jobs not allowed while updating firmware.
0500400B Problem downloading file. Please check network connection and resend print job.
05004001 Failed to connect to Bambu Cloud. Please check network connection.
05004022 Cloud response is invalid. If issue persists, contact customer support.
05014035 Device binding in progress; cannot respond to new binding requests.
05004019 Printer already bound. Please unbind and try again.
05004016 MicroSD Card is write-protected. Please replace the MicroSD Card.
05004029 Cloud access rejected. If issue persists, contact customer support.
05024001 Current filament will be used in this print job. Settings cannot be changed.
05004038 Nozzle diameter in sliced file not consistent with current nozzle setting. Cannot print.
05014029 Cloud access rejected. If issue persists, contact customer support.
05004028 Cloud response is invalid. If issue persists, contact customer support.
05014028 Cloud response is invalid. If issue persists, contact customer support.
05004024 Cloud access failed — network instability, no internet, or router firewall. Check router config.
0500400D Please run a self-test and restart the print job.
05024004 Some features not supported by current device. Check Studio feature settings or update firmware.
0501401F Authorization timed out. Ensure phone/PC has internet and Bambu Studio/Handy is in foreground.
0500400C Please insert a MicroSD card and restart the print job.
05014033 APP region does not match printer; download APP in corresponding region and register again.
0500401B Cloud response is invalid. If issue persists, contact customer support.
05004020 Cloud access rejected. If issue persists, contact customer support.
05008013 Print file not available. Check if storage media has been removed.
05004018 Binding configuration parsing failed; please try again.
0500402E MicroSD card file system not supported. Replace card or format to FAT32.
0500401A Cloud access failed — network instability or router firewall. Check router config.
05004014 Slicing for print job failed. Check settings and restart the print job.
05014024 Cloud access failed — network instability or router firewall. Check router config.
0501401A Cloud access failed — network instability or router firewall. Check router config.
05014031 Device discovery binding in progress; QR code cannot be displayed. Wait or abort and retry.
05004042 Printing and calibration cannot be performed while AMS is drying. Stop drying or connect power adapter.
05004008 Starting printing failed; please power cycle printer and resend print job.
0500C010 MicroSD Card read/write exception: please reinsert or replace the MicroSD Card.
0500402D System exception.
05014025 Cloud response is invalid. If issue persists, contact customer support.
05014022 Cloud response is invalid. If issue persists, contact customer support.
0500401F Authorization timed out. Ensure phone/PC has internet and Bambu Studio/Handy is in foreground.
0500402F MicroSD card sector data damaged. Use SD card repair tool or replace card.
05014018 Binding configuration parsing failed; please try again.
05014020 Cloud access rejected. If issue persists, contact customer support.
05004015 Not enough free storage space. Format or clear files from MicroSD card.
0500409D AMS A firmware does not match printer; cannot continue working. Please upgrade on "Firmware" page.
0587409C AMS-HT H firmware does not match printer; cannot continue working. Please upgrade on "Firmware" page.
05844096 Device cannot detect AMS-HT E. Please reconnect AMS-HT cable or restart printer.
05824096 Device cannot detect AMS-HT C. Please reconnect AMS-HT cable or restart printer.
0502409D AMS C firmware does not match printer; cannot continue working. Please upgrade on "Firmware" page.
05864096 Device cannot detect AMS-HT G. Please reconnect AMS-HT cable or restart printer.
05014098 Device cannot detect AMS B. Please reconnect AMS cable or restart printer.
0582409C AMS-HT C firmware does not match printer; cannot continue working. Please upgrade on "Firmware" page.
0584409C AMS-HT E firmware does not match printer; cannot continue working. Please upgrade on "Firmware" page.
05854096 Device cannot detect AMS-HT F. Please reconnect AMS-HT cable or restart printer.
05874096 Device cannot detect AMS-HT H. Please reconnect AMS-HT cable or restart printer.
05834096 Device cannot detect AMS-HT D. Please reconnect AMS-HT cable or restart printer.
0581409C AMS-HT B firmware does not match printer; cannot continue working. Please upgrade on "Firmware" page.
0586409C AMS-HT G firmware does not match printer; cannot continue working. Please upgrade on "Firmware" page.
05814096 Device cannot detect AMS-HT B. Please reconnect AMS-HT cable or restart printer.
0585409C AMS-HT F firmware does not match printer; cannot continue working. Please upgrade on "Firmware" page.
05004098 Device cannot detect AMS A. Please reconnect AMS cable or restart printer.
05024098 Device cannot detect AMS C. Please reconnect AMS cable or restart printer.
0503409D AMS D firmware does not match printer; cannot continue working. Please upgrade on "Firmware" page.
0580409C AMS-HT A firmware does not match printer; cannot continue working. Please upgrade on "Firmware" page.
05034098 Device cannot detect AMS D. Please reconnect AMS cable or restart printer.
05804096 Device cannot detect AMS-HT A. Please reconnect AMS-HT cable or restart printer.
0583409C AMS-HT D firmware does not match printer; cannot continue working. Please upgrade on "Firmware" page.
0501409D AMS B firmware does not match printer; cannot continue working. Please upgrade on "Firmware" page.
0500C011 SD card performance degraded — may affect printing, logging, and video. Try formatting or replace.
0502400D Failed to start new task: filament loading/unloading not completed.
05004012 Device is printing; cannot upgrade now. Please try again later.
05004013 AMS in operation; cannot upgrade now. Please try again when idle.
05004030 Device currently upgrading. Please try again when idle.
0500400F AMS is initializing; cannot upgrade now. Please try again later.
05004010 AMS is drying; cannot upgrade now. Please try again later.
05004011 Printer is loading/unloading filament; cannot upgrade now. Please try again later.
058440A2 AMS-HT E communication abnormal. Please reconnect module cable or restart printer.
058640A2 AMS-HT G communication abnormal. Please reconnect module cable or restart printer.
058540A2 AMS-HT F communication abnormal. Please reconnect module cable or restart printer.
058240A2 AMS-HT C communication abnormal. Please reconnect module cable or restart printer.
058740A2 AMS-HT H communication abnormal. Please reconnect module cable or restart printer.
050240A3 AMS C communication abnormal. Please reconnect module cable or restart printer.
050140A3 AMS B communication abnormal. Please reconnect module cable or restart printer.
050040A3 AMS A communication abnormal. Please reconnect module cable or restart printer.
050340A3 AMS D communication abnormal. Please reconnect module cable or restart printer.
058140A2 AMS-HT B communication abnormal. Please reconnect module cable or restart printer.
058040A2 AMS-HT A communication abnormal. Please reconnect module cable or restart printer.
058340A2 AMS-HT D communication abnormal. Please reconnect module cable or restart printer.
0502C014 AMS Remaining Filament Estimation is enabled by default and cannot be disabled.
0500803C Current nozzle setting does not match slicing file. Recommended to re-slice before printing.
0502C024 Flow dynamic calibration records exceeded storage limit. Delete some historical records in slicer.
0500403C Current nozzle setting does not match slicing file. Recommended to re-slice before printing.
0502C026 Device busy; cannot perform this operation now. Please try again later.
05004057 Filament selected requires a harder nozzle. Replace nozzle or adjust filament settings.
05024027 Current AMS does not support drying while printing. Update AMS firmware on "Firmware" page.
0500C04F AMS is drying; cannot perform this operation now.
0500C04D Device in laser or cutting mode; cannot start drying.
0500C04B Filament in AMS outlet — high drying temperature may cause blockage. Unload filament first.
0500C04C AMS is currently drying. Please do not start the process again.
0500C04A AMS is calibrating, reading RFID, or loading/unloading material. Unable to start drying.
0500C04E Please connect a power adapter to the AMS-HT before starting the drying process.
05004095 No print plate detected. Please place it correctly and recalibrate on the device.
0502C028 Filament currently loaded in extruder does not support manual feeding.
050040C0 Communication error with AMS, AMS lite, or AMS HT. Reconnect cable or restart printer.
05008057 Filament hardness exceeds current nozzle hardness. May cause nozzle wear. Proceed with caution.
050040A6 File download failed due to missing certificates. Check Fleet Hub certificate config and restart.
0500809B Build plate not properly positioned — may collide with waste chute. Reposition build plate.
050040A8 Device firmware requires repair upgrade. Please upgrade on "Firmware" page.
05024030 Failed to parse G-code file. Task stopped. Please restart the G-code task.
0502402D Printing stopped — unable to parse 3mf file. Please resend your print job.
0502402F Printing stopped — unable to parse 3mf file. Please resend your print job.
0502402E Printing stopped — unable to parse 3mf file. Please resend your print job.
0502C032 Check and remove printed parts or debris from heatbed surface and underside before continuing drying.
0502C031 Check and remove printed parts or debris from heatbed surface before continuing cold pull.
050040B4 Task execution error. Please restart the device. If issue persists, contact technical support.
E-012 P1S error codes — 07xx: AMS filament system (161 codes)open 2026-06-11

Bambu Lab P1S error codes — AMS (standard) filament system errors. Source: BambuStudio hms_en_01P.json

Code Description
07038012 Failed to get AMS mapping table; please select "Resume" to retry.
07058011 AMS filament ran out. Please insert a new filament into the same AMS slot.
07004001 AMS disabled for print but still has filament loaded. Unload AMS filament and switch to spool holder.
07FF8003 Pull out filament on spool holder. If persists, check for filament broken in extruder.
07018013 Timeout purging old filament: check if filament is stuck or extruder is clogged.
07FF8001 Failed to cut the filament. Please check the cutter.
07048003 Failed to pull out filament from extruder — clogged extruder or filament broken inside.
07058016 Extruder not extruding normally; refer to Assistant. If defects acceptable, resume.
07078016 Extruder not extruding normally; refer to Assistant. If defects acceptable, resume.
0703C06D AMS D assisting in filament insertion. Unable to start drying. Try again later.
07068004 AMS failed to pull back filament — stuck spool or end of filament stuck in path.
07028001 Failed to cut the filament. Please check the cutter.
07008010 AMS assist motor overloaded — entangled filament or stuck spool.
07FFC009 Feed filament into PTFE tube until it cannot be pushed any farther.
07018017 AMS B is drying. Stop drying process before loading/unloading material.
07038010 AMS assist motor overloaded — entangled filament or stuck spool.
07038001 Failed to cut the filament. Please check the cutter.
07028013 Timeout purging old filament: check if filament is stuck or extruder is clogged.
07058012 Failed to get AMS mapping table; please select "Resume" to retry.
07014001 Filament still loaded from AMS after disabled. Unload, load from spool holder, restart printing.
0701C069 An error occurred during AMS B drying. Go to Assistant for more details.
07008007 Extruding filament failed. The extruder might be clogged.
07FF8005 Failed to feed filament outside AMS. Clip end of filament flat and check if spool is stuck.
0702C06E AMS C motor performing self-test. Unable to start drying. Try again later.
07FFC008 Pull out filament on spool holder. If persists, check for filament broken in extruder.
07028007 Extruding filament failed. The extruder might be clogged.
07048004 AMS failed to pull back filament — stuck spool or end of filament stuck in path.
0700C06D AMS A assisting in filament insertion. Unable to start drying. Try again later.
07048023 AMS E cooling failed. Ambient temperature may be too high. Operate in suitable environment.
07018010 AMS assist motor overloaded — entangled filament or stuck spool.
07058007 Extruding filament failed. The extruder might be clogged.
07058010 AMS assist motor overloaded — entangled filament or stuck spool.
07028016 Extruder not extruding normally; refer to Assistant. If defects acceptable, resume.
07FF8004 Failed to pull back filament from toolhead to AMS. Check if filament or spool is stuck.
07068011 AMS filament ran out. Please insert a new filament into the same AMS slot.
07FF8011 External filament has run out; please load a new filament.
07024001 Filament still loaded from AMS after disabled. Unload, load from spool holder, restart printing.
0702C06C AMS C is in Feed Assist Mode. Unload filament and try drying again.
0702C06B AMS C is changing filament. Unable to start drying. Try again later.
07038023 AMS D cooling failed. Ambient temperature may be too high. Operate in suitable environment.
07068003 Failed to pull out filament from extruder — clogged extruder or filament broken inside.
07048010 AMS assist motor overloaded — entangled filament or stuck spool.
07018012 Failed to get AMS mapping table; please select "Resume" to retry.
07018005 AMS failed to send out filament. Clip end flat and reinsert. Check PTFE tubes for wear.
07078011 AMS filament ran out. Please insert a new filament into the same AMS slot.
0703C069 An error occurred during AMS D drying. Go to Assistant for more details.
07008023 AMS A cooling failed. Ambient temperature may be too high. Operate in suitable environment.
0701C06C AMS B is in Feed Assist Mode. Unload filament and try drying again.
0702C069 An error occurred during AMS C drying. Go to Assistant for more details.
07058023 AMS F cooling failed. Ambient temperature may be too high. Operate in suitable environment.
07008017 AMS A is drying. Stop drying process before loading/unloading material.
07028017 AMS C is drying. Stop drying process before loading/unloading material.
07018003 Failed to pull out filament from extruder — clogged extruder or filament broken inside.
07038004 AMS failed to pull back filament — stuck spool or end of filament stuck in path.
07048007 Extruding filament failed. The extruder might be clogged.
07024025 Failed to read the filament information.
07FF8002 The cutter is stuck. Please make sure the cutter handle is out.
07008003 Failed to pull out filament from extruder — clogged extruder or filament broken inside.
07058003 Failed to pull out filament from extruder — clogged extruder or filament broken inside.
07004025 Failed to read the filament information.
07038011 AMS filament ran out. Please insert a new filament into the same AMS slot.
07028011 AMS filament ran out. Please insert a new filament into the same AMS slot.
07FF8007 Observe nozzle. If filament extruded select "Done"; if not, push filament slightly then "Retry".
07FF8012 Failed to get AMS mapping table; please select "Resume" to retry.
0701C06B AMS B is changing filament. Unable to start drying. Try again later.
0700C06B AMS A is changing filament. Unable to start drying. Try again later.
07008011 AMS filament ran out. Please insert a new filament into the same AMS slot.
07038007 Extruding filament failed. The extruder might be clogged.
07034025 Failed to read the filament information.
07068005 AMS failed to send out filament. Clip end flat and reinsert. Check PTFE tubes for wear.
07FFC003 Pull out filament on spool holder. If persists, check for filament broken in extruder or PTFE tube.
07028010 AMS assist motor overloaded — entangled filament or stuck spool.
07008004 AMS failed to pull back filament — stuck spool or end of filament stuck in path.
07FF4001 Filament still loaded from AMS after disabled. Unload, load from spool holder, restart printing.
07048016 Extruder not extruding normally; refer to Assistant. If defects acceptable, resume.
07068023 AMS G cooling failed. Ambient temperature may be too high. Operate in suitable environment.
07018016 Extruder not extruding normally; refer to Assistant. If defects acceptable, resume.
07038016 Extruder not extruding normally; refer to Assistant. If defects acceptable, resume.
0701C06E AMS B motor performing self-test. Unable to start drying. Try again later.
0702C06D AMS C assisting in filament insertion. Unable to start drying. Try again later.
07018011 AMS filament ran out. Please insert a new filament into the same AMS slot.
07078003 Failed to pull out filament from extruder — clogged extruder or filament broken inside.
07074025 Failed to read the filament information.
07028002 The cutter is stuck. Please make sure the cutter handle is out.
07028012 Failed to get AMS mapping table; please select "Resume" to retry.
0700C069 An error occurred during AMS A drying. Go to Assistant for more details.
07028004 AMS failed to pull back filament — stuck spool or end of filament stuck in path.
07058005 AMS failed to send out filament. Clip end flat and reinsert. Check PTFE tubes for wear.
07018007 Extruding filament failed. The extruder might be clogged.
07078007 Extruding filament failed. The extruder might be clogged.
07068007 Extruding filament failed. The extruder might be clogged.
07038002 The cutter is stuck. Please make sure the cutter handle is out.
0703C06C AMS D is in Feed Assist Mode. Unload filament and try drying again.
07048011 AMS filament ran out. Please insert a new filament into the same AMS slot.
07078010 AMS assist motor overloaded — entangled filament or stuck spool.
07044025 Failed to read the filament information.
07028023 AMS C cooling failed. Ambient temperature may be too high. Operate in suitable environment.
0701C06A AMS B is reading RFID. Unable to start drying. Try again later.
07018001 Failed to cut the filament. Please check the cutter.
07008001 Failed to cut the filament. Please check the cutter.
07008016 Extruder not extruding normally; refer to Assistant. If defects acceptable, resume.
0700C06E AMS A motor performing self-test. Unable to start drying. Try again later.
07068010 AMS assist motor overloaded — entangled filament or stuck spool.
07008012 Failed to get AMS mapping table; please select "Resume" to retry.
07048005 AMS failed to send out filament. Clip end flat and reinsert. Check PTFE tubes for wear.
07FF8010 Check if external filament spool or filament is stuck.
07064025 Failed to read the filament information.
07028003 Failed to pull out filament from extruder — clogged extruder or filament broken inside.
07008002 The cutter is stuck. Please make sure the cutter handle is out.
07018023 AMS B cooling failed. Ambient temperature may be too high. Operate in suitable environment.
07018002 The cutter is stuck. Please make sure the cutter handle is out.
07068016 Extruder not extruding normally; refer to Assistant. If defects acceptable, resume.
07FFC00A Observe nozzle. If filament extruded select "Continue"; if not, push filament slightly then "Retry".
0700C06C AMS A is in Feed Assist Mode. Unload filament and try drying again.
0700C06A AMS A is reading RFID. Unable to start drying. Try again later.
0703C06B AMS D is changing filament. Unable to start drying. Try again later.
0703C06A AMS D is reading RFID. Unable to start drying. Try again later.
07018004 AMS failed to pull back filament — stuck spool or end of filament stuck in path.
07054025 Failed to read the filament information.
07008005 AMS failed to send out filament. Clip end flat and reinsert. Check PTFE tubes for wear.
0701C06D AMS B assisting in filament insertion. Unable to start drying. Try again later.
07008013 Timeout purging old filament: check if filament is stuck or extruder is clogged.
07078012 Failed to get AMS mapping table; please select "Resume" to retry.
07078005 AMS failed to send out filament. Clip end flat and reinsert. Check PTFE tubes for wear.
0703C06E AMS D motor performing self-test. Unable to start drying. Try again later.
07014025 Failed to read the filament information.
07034001 Filament still loaded from AMS after disabled. Unload, load from spool holder, restart printing.
07078004 AMS failed to pull back filament — stuck spool or end of filament stuck in path.
07078023 AMS H cooling failed. Ambient temperature may be too high. Operate in suitable environment.
07FFC006 Feed filament into PTFE tube until it cannot be pushed any farther.
07FF8013 Timeout purging old filament: check if filament is stuck or extruder is clogged.
07058004 AMS failed to pull back filament — stuck spool or end of filament stuck in path.
07038005 AMS failed to send out filament. Clip end flat and reinsert. Check PTFE tubes for wear.
07038017 AMS D is drying. Stop drying process before loading/unloading material.
07038013 Timeout purging old filament: check if filament is stuck or extruder is clogged.
07FF8006 Feed filament into PTFE tube until it cannot be pushed any farther.
07048012 Failed to get AMS mapping table; please select "Resume" to retry.
0702C06A AMS C is reading RFID. Unable to start drying. Try again later.
07038003 Failed to pull out filament from extruder — clogged extruder or filament broken inside.
07068012 Failed to get AMS mapping table; please select "Resume" to retry.
07028005 AMS failed to send out filament. Clip end flat and reinsert. Check PTFE tubes for wear.
07048006 Unable to feed filament into extruder — entangled filament, stuck spool, or disconnected AMS PTFE tube.
07078006 Unable to feed filament into extruder — entangled filament, stuck spool, or disconnected AMS PTFE tube.
07058006 Unable to feed filament into extruder — entangled filament, stuck spool, or disconnected AMS PTFE tube.
07008006 Unable to feed filament into extruder — entangled filament, stuck spool, or disconnected AMS PTFE tube.
07038006 Unable to feed filament into extruder — entangled filament, stuck spool, or disconnected AMS PTFE tube.
07018006 Unable to feed filament into extruder — entangled filament, stuck spool, or disconnected AMS PTFE tube.
07028006 Unable to feed filament into extruder — entangled filament, stuck spool, or disconnected AMS PTFE tube.
07068006 Unable to feed filament into extruder — entangled filament, stuck spool, or disconnected AMS PTFE tube.
07FF8030 Filament specified in slicer used up. Printing paused. Go to machine to replace material and resume.
07FE8030 Filament specified in slicer used up. Printing paused. Go to machine to replace material and resume.
07FEC030 Filament specified in slicer used up. Printing paused. Go to machine to replace material and resume.
07FFC030 Filament specified in slicer used up. Printing paused. Go to machine to replace material and resume.
0703C008 AMS used for current print is disconnected. Check connection. Will resume automatically after reconnection.
0704C008 AMS used for current print is disconnected. Check connection. Will resume automatically after reconnection.
0700C008 AMS used for current print is disconnected. Check connection. Will resume automatically after reconnection.
0705C008 AMS used for current print is disconnected. Check connection. Will resume automatically after reconnection.
0706C008 AMS used for current print is disconnected. Check connection. Will resume automatically after reconnection.
0707C008 AMS used for current print is disconnected. Check connection. Will resume automatically after reconnection.
0702C008 AMS used for current print is disconnected. Check connection. Will resume automatically after reconnection.
0701C008 AMS used for current print is disconnected. Check connection. Will resume automatically after reconnection.
E-013 P1S error codes — 18xx: AMS-HT filament system (158 codes)open 2026-06-11

Bambu Lab P1S error codes — AMS-HT (high-temperature AMS) filament system errors. Source: BambuStudio hms_en_01P.json

Code Description
1802C06B AMS-HT C is changing filament. Unable to start drying. Try again later.
18078005 AMS-HT failed to send out filament. Clip end flat and reinsert. Check PTFE tubes for wear.
18028007 Extruding filament failed. The extruder might be clogged.
18038012 Failed to get AMS mapping table; please select "Resume" to retry.
1806C06E AMS-HT G motor performing self-test. Unable to start drying. Try again later.
1800C069 Error occurred during AMS-HT A drying. Go to Assistant for more details.
1804C06A AMS-HT E is reading RFID. Unable to start drying. Try again later.
1807C06C AMS-HT H is in Feed Assist Mode. Unable to start drying. Try again later.
1803C069 Error occurred during AMS-HT D drying. Go to Assistant for more details.
18018023 AMS-HT B cooling failed. Ambient temperature may be too high. Operate in suitable environment.
18008012 Failed to get AMS mapping table; please select "Resume" to retry.
18048016 Extruder not extruding normally; refer to Assistant. If defects acceptable, resume.
18038010 AMS-HT assist motor overloaded — entangled filament or stuck spool.
18078016 Extruder not extruding normally; refer to Assistant. If defects acceptable, resume.
18028012 Failed to get AMS mapping table; please select "Resume" to retry.
18018004 AMS-HT failed to pull back filament — stuck spool or end of filament stuck in path.
1802C06C AMS-HT C is in Feed Assist Mode. Unable to start drying. Try again later.
18044025 Failed to read the filament information.
1803C06C AMS-HT D is in Feed Assist Mode. Unable to start drying. Try again later.
1806C06D AMS-HT G assisting in filament insertion. Unable to start drying. Try again later.
18008017 AMS-HT A is drying. Stop drying process before loading/unloading material.
18058004 AMS-HT failed to pull back filament — stuck spool or end of filament stuck in path.
1801C06C AMS-HT B is in Feed Assist Mode. Unable to start drying. Try again later.
18008007 Extruding filament failed. The extruder might be clogged.
18008004 AMS-HT failed to pull back filament — stuck spool or end of filament stuck in path.
1802C06A AMS-HT C is reading RFID. Unable to start drying. Try again later.
1804C06E AMS-HT E motor performing self-test. Unable to start drying. Try again later.
18078011 AMS-HT filament ran out. Please insert new filament into same AMS-HT slot.
18008003 Failed to pull out filament from extruder — clogged extruder or filament broken inside.
18058003 Failed to pull out filament from extruder — clogged extruder or filament broken inside.
18048005 AMS-HT failed to send out filament. Clip end flat and reinsert. Check PTFE tubes for wear.
18058016 Extruder not extruding normally; refer to Assistant. If defects acceptable, resume.
18064025 Failed to read the filament information.
18078012 Failed to get AMS mapping table; please select "Resume" to retry.
18048023 AMS-HT E cooling failed. Ambient temperature may be too high. Operate in suitable environment.
18048010 AMS-HT assist motor overloaded — entangled filament or stuck spool.
1803C06A AMS-HT D is reading RFID. Unable to start drying. Try again later.
18018016 Extruder not extruding normally; refer to Assistant. If defects acceptable, resume.
18068012 Failed to get AMS mapping table; please select "Resume" to retry.
18008010 AMS-HT assist motor overloaded — entangled filament or stuck spool.
18038003 Failed to pull out filament from extruder — clogged extruder or filament broken inside.
18058011 AMS-HT filament ran out. Please insert new filament into same AMS-HT slot.
18018007 Extruding filament failed. The extruder might be clogged.
18038004 AMS-HT failed to pull back filament — stuck spool or end of filament stuck in path.
18028023 AMS-HT C cooling failed. Ambient temperature may be too high. Operate in suitable environment.
1803C06B AMS-HT D is changing filament. Unable to start drying. Try again later.
18038011 AMS-HT filament ran out. Please insert new filament into same AMS-HT slot.
18008023 AMS-HT A cooling failed. Ambient temperature may be too high. Operate in suitable environment.
1800C06A AMS-HT A is reading RFID. Unable to start drying. Try again later.
1807C06B AMS-HT H is changing filament. Unable to start drying. Try again later.
1806C06A AMS-HT G is reading RFID. Unable to start drying. Try again later.
18018011 AMS-HT filament ran out. Please insert new filament into same AMS-HT slot.
1801C06D AMS-HT B assisting in filament insertion. Unable to start drying. Try again later.
18028003 Failed to pull out filament from extruder — clogged extruder or filament broken inside.
18008011 AMS-HT filament ran out. Please insert new filament into same AMS-HT slot.
18008016 Extruder not extruding normally; refer to Assistant. If defects acceptable, resume.
18054025 Failed to read the filament information.
18038017 AMS-HT D is drying. Stop drying process before loading/unloading material.
18018012 Failed to get AMS mapping table; please select "Resume" to retry.
18068005 AMS-HT failed to send out filament. Clip end flat and reinsert. Check PTFE tubes for wear.
18018017 AMS-HT B is drying. Stop drying process before loading/unloading material.
1801C069 Error occurred during AMS-HT B drying. Go to Assistant for more details.
18028017 AMS-HT C is drying. Stop drying process before loading/unloading material.
18FF8005 Failed to feed filament outside AMS-HT. Clip end flat and check if spool is stuck.
18048012 Failed to get AMS mapping table; please select "Resume" to retry.
18048011 AMS-HT filament ran out. Please insert new filament into same AMS-HT slot.
1800C06C AMS-HT A is in Feed Assist Mode. Unable to start drying. Try again later.
18068023 AMS-HT G cooling failed. Ambient temperature may be too high. Operate in suitable environment.
18048004 AMS-HT failed to pull back filament — stuck spool or end of filament stuck in path.
18048007 Extruding filament failed. The extruder might be clogged.
18058005 AMS-HT failed to send out filament. Clip end flat and reinsert. Check PTFE tubes for wear.
18038023 AMS-HT D cooling failed. Ambient temperature may be too high. Operate in suitable environment.
18068016 Extruder not extruding normally; refer to Assistant. If defects acceptable, resume.
18FF8012 Failed to get AMS mapping table; please select "Resume" to retry.
18068004 AMS-HT failed to pull back filament — stuck spool or end of filament stuck in path.
1806C06C AMS-HT G is in Feed Assist Mode. Unable to start drying. Try again later.
18058010 AMS-HT assist motor overloaded — entangled filament or stuck spool.
1802C069 Error occurred during AMS-HT C drying. Go to Assistant for more details.
1807C06D AMS-HT H assisting in filament insertion. Unable to start drying. Try again later.
1805C06A AMS-HT F is reading RFID. Unable to start drying. Try again later.
18038005 AMS-HT failed to send out filament. Clip end flat and reinsert. Check PTFE tubes for wear.
18028010 AMS-HT assist motor overloaded — entangled filament or stuck spool.
1801C06B AMS-HT B is changing filament. Unable to start drying. Try again later.
1804C06B AMS-HT E is changing filament. Unable to start drying. Try again later.
18024025 Failed to read the filament information.
1805C06B AMS-HT F is changing filament. Unable to start drying. Try again later.
1806C069 Error occurred during AMS-HT G drying. Go to Assistant for more details.
18028004 AMS-HT failed to pull back filament — stuck spool or end of filament stuck in path.
18074025 Failed to read the filament information.
1805C06C AMS-HT F is in Feed Assist Mode. Unable to start drying. Try again later.
1802C06D AMS-HT C assisting in filament insertion. Unable to start drying. Try again later.
1806C06B AMS-HT G is changing filament. Unable to start drying. Try again later.
1803C06D AMS-HT D assisting in filament insertion. Unable to start drying. Try again later.
18058012 Failed to get AMS mapping table; please select "Resume" to retry.
18058007 Extruding filament failed. The extruder might be clogged.
18068007 Extruding filament failed. The extruder might be clogged.
1807C06E AMS-HT H motor performing self-test. Unable to start drying. Try again later.
18068011 AMS-HT filament ran out. Please insert new filament into same AMS-HT slot.
18038007 Extruding filament failed. The extruder might be clogged.
18014025 Failed to read the filament information.
18078004 AMS-HT failed to pull back filament — stuck spool or end of filament stuck in path.
1805C06E AMS-HT F motor performing self-test. Unable to start drying. Try again later.
18078023 AMS-HT H cooling failed. Ambient temperature may be too high. Operate in suitable environment.
1804C06D AMS-HT E assisting in filament insertion. Unable to start drying. Try again later.
18068003 Failed to pull out filament from extruder — clogged extruder or filament broken inside.
1801C06E AMS-HT B motor performing self-test. Unable to start drying. Try again later.
18028016 Extruder not extruding normally; refer to Assistant. If defects acceptable, resume.
18058023 AMS-HT F cooling failed. Ambient temperature may be too high. Operate in suitable environment.
18078007 Extruding filament failed. The extruder might be clogged.
1800C06B AMS-HT A is changing filament. Unable to start drying. Try again later.
1800C06E AMS-HT A motor performing self-test. Unable to start drying. Try again later.
18018010 AMS-HT assist motor overloaded — entangled filament or stuck spool.
18008005 AMS-HT failed to send out filament. Clip end flat and reinsert. Check PTFE tubes for wear.
18018005 AMS-HT failed to send out filament. Clip end flat and reinsert. Check PTFE tubes for wear.
18034025 Failed to read the filament information.
1804C06C AMS-HT E is in Feed Assist Mode. Unable to start drying. Try again later.
18028011 AMS-HT filament ran out. Please insert new filament into same AMS-HT slot.
1805C069 Error occurred during AMS-HT F drying. Go to Assistant for more details.
1803C06E AMS-HT D motor performing self-test. Unable to start drying. Try again later.
18068010 AMS-HT assist motor overloaded — entangled filament or stuck spool.
18078003 Failed to pull out filament from extruder — clogged extruder or filament broken inside.
1804C069 Error occurred during AMS-HT E drying. Go to Assistant for more details.
1802C06E AMS-HT C motor performing self-test. Unable to start drying. Try again later.
18004025 Failed to read the filament information.
18078010 AMS-HT assist motor overloaded — entangled filament or stuck spool.
1801C06A AMS-HT B is reading RFID. Unable to start drying. Try again later.
1800C06D AMS-HT A assisting in filament insertion. Unable to start drying. Try again later.
18028005 AMS-HT failed to send out filament. Clip end flat and reinsert. Check PTFE tubes for wear.
1807C06A AMS-HT H is reading RFID. Unable to start drying. Try again later.
18048003 Failed to pull out filament from extruder — clogged extruder or filament broken inside.
1807C069 Error occurred during AMS-HT H drying. Go to Assistant for more details.
1805C06D AMS-HT F assisting in filament insertion. Unable to start drying. Try again later.
18038016 Extruder not extruding normally; refer to Assistant. If defects acceptable, resume.
18018003 Failed to pull out filament from extruder — clogged extruder or filament broken inside.
18018006 Unable to feed filament into extruder — entangled filament, stuck spool, or disconnected AMS-HT PTFE tube.
18008006 Unable to feed filament into extruder — entangled filament, stuck spool, or disconnected AMS-HT PTFE tube.
18078006 Unable to feed filament into extruder — entangled filament, stuck spool, or disconnected AMS-HT PTFE tube.
18028006 Unable to feed filament into extruder — entangled filament, stuck spool, or disconnected AMS-HT PTFE tube.
18048006 Unable to feed filament into extruder — entangled filament, stuck spool, or disconnected AMS-HT PTFE tube.
18058006 Unable to feed filament into extruder — entangled filament, stuck spool, or disconnected AMS-HT PTFE tube.
18038006 Unable to feed filament into extruder — entangled filament, stuck spool, or disconnected AMS-HT PTFE tube.
18068006 Unable to feed filament into extruder — entangled filament, stuck spool, or disconnected AMS-HT PTFE tube.
1806C008 AMS used for current print is disconnected. Check connection. Will resume automatically after reconnection.
1804C008 AMS used for current print is disconnected. Check connection. Will resume automatically after reconnection.
1807C008 AMS used for current print is disconnected. Check connection. Will resume automatically after reconnection.
1800C008 AMS used for current print is disconnected. Check connection. Will resume automatically after reconnection.
1802C008 AMS used for current print is disconnected. Check connection. Will resume automatically after reconnection.
1803C008 AMS used for current print is disconnected. Check connection. Will resume automatically after reconnection.
1805C008 AMS used for current print is disconnected. Check connection. Will resume automatically after reconnection.
1801C008 AMS used for current print is disconnected. Check connection. Will resume automatically after reconnection.

Issues

E-004 Zeus — filament not feeding through; extruder gears worn out info open 2026-06-11

Symptom: Zeus could not push filament through. Cleaning the nozzle multiple times did not help.

Root cause: Extruder gears were worn down and could not grip the filament properly.

Fix: Replaced the entire extruder gear assembly (faster than replacing individual gears).

Date resolved: approx. 2025-05-23 (same service event as hardened steel nozzle upgrade).

E-005 Hades — filament completely stuck in extruder, could not retract info open 2026-06-11

Symptom: Hades could not retract filament from the extruder. Filament was completely jammed — the retract command did nothing.

Root cause: Filament had seized inside the extruder (likely heat creep or a cold pull failure that hardened in place).

Fix: Had to disassemble the extruder to physically pull the filament out with pliers.

Lesson: If retraction fails completely and the normal unclog procedure doesn't work, disassemble and use pliers — do not force the motor as it risks stripping gears.

Notices

E-006 Hades — service history info open 2026-06-11

2025-05-23: Replaced hardened steel nozzle and extruder gears (upgrade from standard).

2025-12-05: Replaced PTFE tube inside AMS port 1 — had worn through/developed a hole.

E-007 Posedion — service history info open 2026-06-11

2025-05-23: Replaced hardened steel nozzle and extruder gears (upgrade from standard).

E-008 Zeus — service history info open 2026-06-11

2025-05-23: Replaced hardened steel nozzle and extruder gears (upgrade from standard). Root cause: extruder gears were worn and could not grip filament — see issue E-004.

2025-08-26: SD card replaced.

ETT00000011 · Rev R0 · 3D Printer Service Book Generated 2026-07-26 14:05 UTC · Trace